- Products (30)
- Blog & News (2)
Go with the Accuride Original line of motion hardware. Complete with enhanced strength and movement, full-extension, and a lever-disconnect, the 3832E model is a classic drawer slide that fits a wide range of uses including but not limited to: pull-out shelves, kitchen utensil drawers, and point-of-sales trays. * Supports loads up to 100 lbs. * For drawers up to 24” wide * For additional technical information see below A patented Cam Drawer Adjust allows for precise vertical adjustment, while a…
Compatible with our 123 Flipper Door Slide, this inset base kit includes black 35mm clip-on hinges as well as #6, #8, and M6 Euro screws--plus pivot blocks and one “Caution” sticker.
- SS0116-CASSRC SS0116-CASSRC 116RC Cassette with Stainless Steel Bearings$192.48
Return to 116RC Product Detail Report Available as a single component or within a kit for our 116RC Linear Track System, this cassette model is crafted with stainless steel ball bearings for added strength, providing unerring endurance to your design’s overall function. Easy-to-install and available for flat- or side-mounting, this stainless steel ball bearing carriage adds heavy-duty seamless, smooth motion to your aluminum track hardware.
- CB0116-CASSRC CB0116-CASSRC 116RC Cassette with Polymer Bearings$192.48
Return to 116RC Product Detail Page Extra Quiet + Renowned Quality. Sold as a single, extra component or within the 116RC kit, this cassette provides flawless, linear motion to aluminum track systems with the use of polymer bearings that guarantee silenced operation. Easy-to-install and available for flat- or side-mounting, this polymer ball bearing carriage adds smooth and reliable motion to your hardware of choice.
Return to 116RC Product Detail Page Ensuring ease from start to finish. Engineered specifically for the 116RC model, these aluminum end stops ensure that your linear track system ends its length of travel safely and soundly--without slamming or rattling shut. Each order comes with two end stops crafted from corrosion-resistant aluminum and two screws for a breezy installation.
Return to 116RC Product Detail Page Structural support for load-bearing walls. A component within the Sliding Door Hardware Kit for the 116RC Heavy-Duty Linear Track System, this support beam anchors your motion hardware securely for tried and true performance that endures the test of time.
Return to 116RC Product Detail Page Extra smooth movement and proven endurance. Specially engineered for the 116RC Sliding Door Hardware Kit, this door bracket kit helps protect your linear track system’s carriages when a damper (CB0116-DAMP) is installed to cushion a fixture’s end of travel.
Return to 116RC Product Detail Page The sum of its parts. A component within the Sliding Door Hardware Kit for the 116RC Heavy-Duty Linear Track System, this 142” fascia is crafted from anodized aluminum and clips onto its support beam (AL0116-SUPPRC) for a sleek, completed design. For extra easy-access, an installer can lift and hook the fascia open to reach the track and fittings responsible for linear motion.
Return to 116RC Product Detail Page For robust hardware with a soft side. An optional component for our 116RC Heavy-Duty Linear Track System, this damper cushions and decelerates the last 1.6” of your hardware’s travel for reduced vibration and migration while also providing a smooth, gentle return every time. With the use of this optional damper, end stops are no longer required. However, recycling brackets (SS0166-BRKT01RC) will be needed to protect the carriages, and sliding door fixtures…
Made to accompany our 3135EC, this bracket kit aids in easy-access installation for rear-facing frames and fixtures in need of concealed hardware. Including two rear brackets with a clear zinc finish, this kit also contains six #8 x ⅝” screws and an installation guide--all inside a polybag. This kit is also RoHS-compliant and available for bulk orders.
Return to 116RC Product Detail Page Finishing touches for sliding door hardware. Engineered for the 116RC Door Hardware Kit, these fascia end caps stabilize the anodized aluminum fascia board on its support beam, specifically for use with track systems on sliding doors. Each order comes with two fascia end caps and eight screws for a thorough installation and robust solution.
Compatible with our 1332 solution and accommodating pocket doors ¾” to 13/16” thick, this hinge kit provides the extra tools you need for an inset installation. Each order includes two 35mm salice black clip-on hinges, two 3mm mounting base plates, two 3mm hinge base spacers, two hinge arm cover caps, four #6 x ⅝” Phillips flat head screws, and one “Caution” door sticker.